If you are worried about the stains, dirt, and spillage in the kitchen, then it is better to protect the walls with kitchen splashbacks and worktops. Splashbacks are lower maintenance in comparison to other wall covers and tiles. Also, you may get various options in designs and colours if you choose that.
You should not splashback every inch of the wall in the kitchen. Try to target the areas above the sink and cooker. From the water damage to the oily splash, these are the areas that come under fire. A glass splashback may act as the focus point for attracting the designer or cooker sink.
Tips to Install the Splashback for Kitchen
There are various materials for splashbacks, but glass splashback is the most popular one that is made of glass, stainless steel, laminated, acrylic, copper, brass, and sheet metals. The additional kitchen wall ideas include tiles, paneling, and vinyl wallpaper.
You should always go through the necessary instructions while buying a kitchen splashback. You need adhesive or tools to set the splashback for the kitchen. Here are the ways to set the splashback:
- Create the Preparation of the Surface
Preparation plays a vital role with the dividend set-up for attaching the glass splashback on your wall. The surface of the splashback is dry, non-porous, flat, and dust-free. You will need to make up the holes in the filler if you are planning to rip off the splashback panel in your kitchen. You would need a non-porous surface that doesn’t suck up the adhesive. It will be better to choose the fresh plaster with primer, PVA, and thin coat.
Along with the length of timber, the spirit level of the surface works properly without any issue. The uneven surface may cause cracks on acrylic, glass, and the edges on the splashback.
- Customise the Size of the Kitchen Splashback
The simplest route for customising the glass splashback depends on the right measurement. You may purchase a standard size of panels in splashback with the vast range of sizes. This allows you to skip the steps easily with the vast range of products. The popular panel sizes of the splashback are 90cm x 75cm, 60cm x 75cm, and 100cm x 75cm.
There are some dimensions that you should check while chipping the material. You should lay on a glass splashback for the kitchen with the soft material for avoiding tear and wear. You may cut down the sand edges in a protective film with the surrounding cabinets. You may work on the functionalities to prove the dimension of the splashback in a customised way.
- Mark the Position of the Splashback
While fixing the single splashback panel, you should carefully use the center on the cooker or sink to position above the kitchen head parts. Suppose you are going full width with the splashback, you need to mark out the height of the panel in the kitchen to fix it straight.
You may also aim for at least 11 cm with the gas hob, 10 cm with the electric, and other instructions with the selected splashbacks.
- Start Applying Adhesive
The out-sized or heavy splashbacks need screws for fixing the wall with adhesive. You can use metal, regular glass, and sheet-style splashbacks with low modulus silicone adhesive and double-coated foam tape. For the extra adhesive, purchase pre-applied sticky backing and splashbacks.
You may apply the strips of foam tape from the top to bottom. You may use a silicone gun and adhesive between the wav-patterned areas. You should not go crazy, and aim for coverage with 2-3 cm wide gaps.
- Fix Glass Splashback to the Wall
You may remove the protective strip of the foam tape that is firmly attached to the splashback on the wall. You should know the position of the fixing. Try to use gentle pressure for checking the spirit level that is straight.
If the splashback is adhered to the wall, you may remove the visible gaps by the sealing of the edge. You may use masking tape for holding the positions of the adhesive set. Check out the parts for 24 hours on the level of the guidance.
- Try to Seal the Joints
The adhesive parts are completely managed to set up with masking tape. You may apply silicone sealant and thin line to manage the edges of the panel. You may take care of your joint by setting up the worktops and splashback. A kitchen grade silicone ensures the maintenance of the watertight seal for preventing the mildew stains.
You may consider the frame of the splashback for the shelf trimming strips. While framing the splashback, you may choose the part of the kitchen designer for the set-up of the seals in the joints.
- Add Protective Finish
Splashbacks are made of acrylic, glass, laminate, and stainless steel, which don’t need further treatment for protecting the spills and splashes. If you are installing the metallic splashback that is made of copper, brass, and bronze sheet, you should work on the protection plan. You should choose the sealant and coating for the protective finish.
The direct exposure can help in managing the moisture with a mottled patina that is gradually needed to be maintained with usage of time. Many people love the aged looks on their wall. If you are one of them, you may apply the thin layer that is made of perfect foam paint roller.
FAQs
- Is it easy to fit kitchen splashbacks?
The splashback materials are perfect for new installation with fabricated surfaces such as composite quartz and stones. There are various options for the DIYers to choose kitchen splashbacks. You may get many options and several companies that provide the range of materials. You may use the self-adhesive backings to set up the thin and lightweight splashback.
- While fitting the joint lines how can you avoid the splashback?
There are a variety of dimensions that are commonly related to the splashback setup with space. The joining options depend on the object and the material that has a neat connection. For butting the panels, you can match the colours of the watertight seal.To manage the dimension and the set-up of the splashback, it is important to look after the changes on the basis of the kitchen cabinet.
- What are the easiest splashback kitchen panels to fit in your kitchen?
The aluminum panel is easy to install and straightforward. The inclined parts can help in carrying the drilled and standard tools. The purpose-made splashbacks can be the great option for creating uniform and sleek looks. Get expert help to manage the setup of the kitchen.
- What is the process to stick splashback on the wall?
You may use some options to stick the splashback on the wall. The first one is the neatest visible fixing with the adhesive. There are some splashbacks that can adhere with the double-sided sticky tape with the combination of tape and sealand along with the silicone dries.
You may read the installation instructions that can help you in setting up the silicone to the wall. There is a low-modulus sealant that is stretched with the setting in an easy way.
The second way of sticking the splashback to the wall is the usage of screws. Generally, you need pre-drilled holes, plugs, and requisite screws that are important for setting it on the wall. You don’t need to screw up the splashback, if you can put it up with the shelf. You may over tighten the screws.
Try to use rubber washers for managing the setup easily. Wrong tightening effect may lead to damage and crack of the splashback. You can deal with the basic functionalities in an effective way.
Bottom Line
It is fine to choose splashback for the kitchen, but if you want to manage the setting of the kitchen, it is necessary to deal with the function. You may also follow the aforesaid tips for setting the splashback.Â
You have to face any issues regarding the kitchen set up. Use the balanced way or take professional help to set up the splashback. The professional help is always valuable if you follow it properly without any issue.
